Kiln Furniture for MLCC Firing

Flat, light and dimensionally stable, so every layer fires the same.

In MLCC firing, details decide the yield. A few tenths of a millimetre of warp in a setter, a few dozen grams of extra rack weight, or one spot of coating loss at a mesh edge can each turn into a yield problem for the whole batch.

We supply setter racks, zirconia-coated nickel mesh, setter plates and pusher plates to MLCC lines, and we know how they behave in pusher kilns and roller hearth kilns under reducing atmosphere. From selection and sample trials to problem analysis in production, we work alongside your process engineers.

approx. 450,000
Setter racks delivered (as of October 2026)
approx. 150,000
Zirconia-coated nickel meshes delivered
In production use
At several leading MLCC producers in China

Typical MLCC firing conditions

Kiln furniture has to stand both long exposure to high temperature and a reducing atmosphere.

Temperature
Long soaks at high temperature. Tell us your peak temperature and soak time, and we check which grade fits.
Atmosphere
Reducing atmosphere (nitrogen with hydrogen) to protect the nickel inner electrodes. This decides which furniture you can use: nickel mesh and uncoated plates behave differently here.
Kiln type
Pusher kilns and roller hearth kilns in production. Elevator and bell kilns for small batches and development.
Loading
Racks with mesh stacked in layers, or footed setter plates. The higher the stack, the more flatness and strength matter.

Five things MLCC lines care about

ConcernWhy it mattersWhat we do
FlatnessWarp in the kiln furniture becomes deformation in the productFlatness depends on size, thickness and formulation. There is no single figure, so we confirm it for your size
Weight and sizeRoller hearth kilns are sensitive to rack weight. Automated lines accept almost no dimensional deviationWe confirm size, weight and layer spacing against your kiln and loading before making samples
Service lifeA broken rack or coating loss on a mesh stops the line for a furniture changeRacks are developed for strength. On mesh we focus on an even coating and the edge finish. We do not quote a service life, because it depends on your conditions
Batch consistencyA good sample does not guarantee good productionStart with a small production batch and agree the acceptance criteria in advance
Quality documentsLarge producers ask for 8D reports, change notices, lot traceability and inspection reportsAn inspection report can accompany each shipment. 8D reports on request

Products used in MLCC firing

Four products cover the main positions in the kiln: carrying the chips, serving as the base plate, moving the load through the kiln, and helping binder burnout.

MAIN SET FOR MLCC
Setter racks with zirconia-coated nickel mesh
Setter rack
99% dense alumina: Al₂O₃ 99.6%, bulk density 3.89 g/cm³, apparent porosity 0.3%, flexural strength 186 MPa, maximum service temperature 1400 °C (typical values).
Standard sizes: square approx. 250 × 250 mm, long approx. 300 × 150 mm. Custom sizes on request.
Nickel mesh
Zirconia coating 35–150 μm, to order. Mesh count to order; 32 mesh is the most common. Standard sizes 230 × 230 mm and 270 × 140 mm, matched to the racks. Sold as a set or separately; custom sizes on request.
For reducing or inert atmosphere only, below approx. 1300–1400 °C. Not for use in air.
Product page: MLCC Setter Racks & Zirconia-Coated Nickel Mesh
Zirconia-coated and footed setter plates (86C-7)A common MLCC base plate. With the zirconia coating it can be used in N₂-H₂ atmosphere. Uncoated 86C-7 cannot. Pusher plates (86C-3)The only grade we supply as a pusher plate. About 1400 °C long-term. Above 1500 °C its wear resistance is not enough. High-porosity alumina plate (99DK)Permeable and high-purity, which helps binder burnout. Not load-bearing: use it as an underlay only.

Getting the most from the furniture

Most furniture problems come from atmosphere, support and heating curve rather than from the material itself.

Confirm the atmosphere first. Nickel mesh works only in reducing or inert atmosphere.
Use the mesh with a rack. Supported only by spacers on four sides, the mesh may warp.
Pre-fire new furniture, usually once, until it no longer affects the product.
Keep racks below about 1400 °C long-term, and do not lift a rack by one corner.
A pale green mesh is normal. It is the mesh changing color and does not affect use.
Go from sample to production in steps. Heat is less even in a full kiln, so the curve may need adjusting.
CASE · CUSTOMER NOT NAMED
Setter racks breaking in long-term use
Problem
Racks used long-term at about 1300 °C in N₂-H₂ atmosphere developed breaks and hidden cracks.
What we did
Together with the customer, we changed both the structure and the material of the rack.
Result
Rack strength improved clearly. We have no before-and-after figures that we can publish.

Questions MLCC engineers ask

Why do setter racks break?
Three common causes: the long-term temperature is too high (keep it below about 1400 °C); the rack is supported differently in use than it was when fired, so stress concentrates; or it is lifted by one corner. If racks still break, send us your kiln type, loading and photos of the break.
Why does the zirconia coating come off the mesh?
Usual causes are oxygen in the atmosphere, an uneven coating, or poor adhesion. The mesh must be used in a reducing or inert atmosphere.
The sample passed. Why did the defect rate rise in volume production?
In a full kiln the middle and the edges heat unevenly, and loading, kiln type and raw material lots also play a part. Start with a small batch and adjust the curve for production.

Ask about MLCC kiln furniture

Send the product and size for a price, or describe your line for a recommendation. Only your email is required. We usually reply within 1–3 business days, and can arrange a sample.

Send inquiry
IF YOU WANT A RECOMMENDATION, THESE HELP
  • Kiln type: pusher, roller hearth or other
  • Maximum temperature and soak time
  • Atmosphere, for example the N₂-H₂ ratio
  • The furniture sizes you use now, and the problem you see