Porous Alumina Setters

Let binder gases out. Keep products from sticking.

Injection-molded ceramics and MIM parts contain a lot of organic binder. During debinding it has to break down and leave the part little by little. If the gases cannot escape, defects stay inside the part and sintering yield drops. Some products also stick to the setter during debinding or sintering.

Our porous setters are made for these two problems. They are 99.5% alumina formed into an open three-dimensional lattice: gases pass through the plate, and the product touches far less of the surface. For ordinary sintering a dense setter is enough. When gases cannot get out or products stick, a porous setter is the better choice.

99.5% Al₂O₃
High purity, low impurities
1550 °C
Maximum service temperature at near-zero load
52%
Apparent porosity (typical)
Samples
Available to test in your own kiln

Choose a structure

Both structures use the same material and have the same properties. In most cases start with G4-1. Choose G5-1 when the product surface must not show a pattern.

TypeStructureMax. service temperatureBest forNote
G4-1 (first choice)Open 3D lattice, high permeability1550 °CMost debinding and firing jobs. If unsure, try this one firstThe lattice pattern can imprint on the product
G5-1Finer structure: flat top face, wave structure underneath1550 °CProducts with sensitive surfacesPlace the product on the flat face
99DK (see Setter Plates)High-porosity alumina plate, about 70% porosity, no through-holes1700 °COur first recommendation for debinding; also when the lattice pattern is a concernNot load-bearing
Dense setter plates (see Setter Plates)Not permeable1700 °COrdinary sintering without gas or sticking problems; heavier products—

Maximum service temperature is a property of the material at near-zero load. The heavier the product on the plate, the lower the usable temperature, so please tell us the load when you ask.

Typical values

PropertyG4-1 / G5-1
Al₂O₃99.5%
SiO₂0.08%
Fe₂O₃0.03%
Bulk density2.04 g/cm³
Apparent porosity52%
Flexural strength29 MPa
Max. service temperature1550 °C (near-zero load)

Typical values (averages), not guaranteed values. Specification values are agreed in the technical agreement.

Sizes

Standard size for trials: square 150 × 150 × 2 mm; disc Ø40 × 10 mm
Start your trial with the standard size, so you can test without waiting for new tooling. Once the trial passes, we discuss larger sizes for production.
Double-side ground plates are available when flatness matters.

Why porous

  • Volatiles leave through the lattice, so debinding is more even
  • Small contact area reduces sticking and reactions with the product
  • 99.5% alumina with very low impurities does not contaminate the product
  • Stronger than the high-porosity 99DK plate (flexural strength 29 MPa vs. about 9 MPa)

Where it is used

  • Debinding of alumina, zirconia and other technical ceramic parts
  • Ceramic injection molding (CIM)
  • Metal injection molding (MIM): debinding and heat treatment
  • Ceramic products that tend to stick to the setter
  • HTCC firing, silicon nitride substrate debinding, dielectric filters, thin alumina substrates

How to use it

The most common problem after switching to porous setters is not adjusting the heating curve.

Use single plates; do not join plates. Products on a joint tend to deform.
Plates can be stacked. For heavier products, use thicker plates.
Heat and cool slowly. Not for rapid heating or quenching.
Lower the heating rate after switching. Binder leaves faster, so the old curve becomes too fast and product corners may crack.
For tight flatness, choose double-side ground plates.
Against warping, use one below and one above: the top plate adds light pressure.
Verify thickness and use in your own debinding process. Start with a small trial.

Questions about porous setters

The lattice pattern shows on my product. What can I do?
The mark is the shape of the plate surface, not a reaction between plate and product. If the product is ground after firing, it does not matter. For sensitive surfaces, switch to G5-1 and place the product on the flat face.
I switched to porous setters and my products started cracking. Why?
Porous setters let the binder out faster and more completely, so your old heating curve is now too fast and corners crack. Lower the heating rate after switching.
What is the highest temperature I can use?
The material is rated to 1550 °C at near-zero load. How hot you can actually go depends on the weight on the plate: the heavier the product, the more easily the plate deforms, and a very heavy product can bend a plate even at 1000 °C. Tell us your temperature and load, and we suggest a thickness or a dense setter instead.
Porous setter or the high-porosity 99DK plate?
99DK gives the best debinding and is our first recommendation; if the lattice pattern on your product is a concern, choose 99DK. In practice, use whichever works in your process. If both work, choose the more cost-effective one. Note that 99DK cannot carry load.
Can you make larger plates?
Yes. We ask you to trial with the standard 150 × 150 × 2 mm size first, so each test does not need a new size. Once the trial passes, we discuss the size you need for production.
RELATED

Get a quote for porous setters

Structure, size and quantity are enough for a price. Only your email is required. We usually reply within 1–3 business days.

Not sure which structure fits? Tick the recommendation box and add your process. Samples are available.

Email: sales@youka-tech.com

PRODUCT: POROUS ALUMINA SETTERS

Loading the form…

We use your details only to answer your inquiry. See our Privacy Policy.